Best Price Porter Cable PSH1 For Sale. Buy Now!.
Read more Porter-Cable PSH1 Gravity Feed Spray Gun
This thing is amazing for the price. Made me a pro. Super easy to use as well, but definitely get the 2.0mm insert. I tried latex paint (thinned) with the 1.5 and it was a big problem.
Have fun!
I'm very happy with this spray gun. This is my first spray gun and I found it very easy to use, it just took some practice to adjust the spray.
This is a good gun. Need to get the settings right; they are not adjusted from the factory at all. Here's what worked for me, after MUCH experimentation, when spraying Zar Ultra Max Urethane.
'X' marks the spot:
AV (Air Volume) at bottom of gun:
Open / Down / Increase 0 - - - 1 - - X 2 - - - Closed / Up / Decrease
PA (Pattern Adjust) on left of gun:
Open/CCW 0 - - - 1 X - - 2 + Closed/ClockW
FC (Fluid Control) at upper back:
Open / Out /Increase 0 - - - 1 - - - 2 - - - 3 - - - 4 - - - 5 - - - 6 - - - X - - - 8 - - - 9 - - - Close/Decrease
Regulator on gun: 45 to 50 psi, and on the compressor itself, 95-100 psi (see mfgr's recommended limits for the gun).
Use this sprayer for custom kids furniture with the 2.2 mm tip and thin the paint. Mostly oil based enamels or metallic latex based coats. I get excellent results as long as the coats are dry between. I also use the 3M spray kit(disposable cups with filters built in) from Rockler for quick clean-up. Thicker material requires higher pressure unless thinned properly, but best results come from proper thinning and patience.
We are redoing our kitchen on the cheap, and decided to repaint our cabinets. After applying TSP and liquid sandpaper to the doors, we put on the water based primer using the 2.2mm Nozzle. Went on very smooth, and the gun has very little overspray. After primer, put on 3 coats of Behr latex paint (also using the 2.2mm nozzle). I didn't even need to thin the paint. It went on so well, I couldn't believe I hadn't found this earlier in life. Make sure to wear a chemical mask for painting purposes. We painted everything in our garage, and used drop cloths where we were painting.
To address some main points:
1) I went straight to using the 2.2mm nozzle as other reviewers suggested. I did not have to thin any of my latex paint. If you live in New England (like I do), keep your paint indoors until ready to use, so it doesn't get cold and thicken up. I used my pancake compressor for the coat of primer on 20 cabinet doors and a few drawers. It takes a long time doing it this way, b/c the compressor is only 6 gallons, and has to run constantly. If you just have a few pieces to spray, you will be fine. But I would recommend using a larger compressor for big jobs.
2) This was my 1st time using a HVLP gun, so I didn't know how to properly clean it (wear glasses/gloves, as paint thinner burns). What I did was this. After you finish spraying, and remove the plastic cup's screw top, then unscrew the whole cup from the gun. Dispose of any paint left in the cup. Be sure to clean the cup's top, and remove the air valve at the top and clean paint from it too. Otherwise, if the air valve gets clogged, it will not let out much, if any paint (happened to me). When you are cleaning the cup, clean the threads too by using some q-tips or a rolled up paper towel.
3) Fill up a disposable plastic container half way with a cleaner (I used paint thinner). Disassemble the front sprayer, and then the nozzle behind it. Clean as much paint off of these with paper towels and q-tips, then place them in the paint thinner and scrub with an old toothbrush, or the pipe cleaner that came with the gun. Now that those are clean, remove them from the paint thinner, and move onto the gun.
4) Now, you should just have the needle exposed on the gun. Set the gun to around 50psi of pressure at the control valve, and spray the excess paint into paper towels. Disconnect the gun from the compressor hose. Remove the needle by unscrewing the back, being careful not to loose the spring. Simply take out the needle, and clean it along with the inside of the gun, in paint thinner. I found the hardest part to be cleaning the paint in the very back of the brass chamber. Use a combination of the pipe cleaner, toothbrush and some q-tips to get it clean.
5) Now that its all clean, reassemble so that it is ready for the next use. Cleanup takes about 20 minutes once you get used to it. The gun is great, and the finish it put out looks like it came from a factory. I did roller my cabinet bases, as I didn't feel like masking off my whole kitchen to spray the bases.... Hope this summary helps those of you on the fence about this HVLP gun.
in all, I am very impressed with the craftsmanship and performance of this tool. However, it has not been easy as a relative beginner with spray painting to learn how to use this particular tool. first of all, I cannot say enough about the quality of the construction of this tool: fine chrome on the outside and turned brass around the spray nozzle. The only thing which would help me to better rate the construction of this tool would be for porter-cable to include a case, which for an item of this quality I feel should be included.
I think however, a few cautionary notes would be helpful to you if you are considering adopting this gun for new spraying project. first of all this gun is difficult to clean. They do include a nice brush made with the correct dimensions that works very well to clean this gun but still, there is a large amount of cleaning that has to happen on the many multifaceted and intricate surfaces inside the gun. Since I don't use a tool like this regularly I am not sure what the standard of cleanliness is and I spend a long amount of time after each use bringing the gun back to its original condition, perhaps this is not necessary but it considerably adds to the time required to use this tool.
Make sure to keep paint from drying on the air inlet attached paint bucket. Over time I've cleaned out every part of the gun except for the top of the paint can which collected enough paint inside it to block any incoming air. This created a large problem when I tried to use the tool in that I was not able to get any paint to come out of the gun and so I increased the pressure and opened all the apertures only to find that I still was not able to get any paint out. I proceeded to water down the paint hoping to reduce its viscosity to no effect. I finally figured out that to make the gun work I needed to keep taking the lid off to let the pressure rebalance in the paint can. I was finally able to clean out the paint can in the gun worked perfectly. The most helpful advice I could give them is that it is important to clean out the surfaces that the gun uses such as the nozzle and the top of the paint can while perhaps spending less time on cleaning the rest of the gun. However, as I said before this gun has not disappointed me in any way from its workmanship and is provided a great transitional tool for me to learn about paint spraying.
I also did not find the overspray from this gun to be that bad even though it just so happened that every time I worried about it I feel that I overcompensated with tape and drop cloths and whenever I didn't worry about it I inevitably hit something small that was very difficult to clean up. However, the overspray from this gun has impressed me as being much less a worry that I previously thought.
I finally put the gun to task after begging for a day off from work. The sprayer made quick work of my patio cover rehab. Be sure to purchase the 2.2 mm nozzle kit, the 2.0 nozzle kit and the 20 oz. metal can. I used the 2.0 nozzle to prime and the 2.2 to spray quality oil-based high-gloss paint. (Minor clogging with the primer on the 2.0 nozzle-switch to the 2.2 nozzle halfway through the oil-based painting part with much better results). The sprayer performed extremely well. Be sure to dilute your liquid to recommended specifications. (Many reviews have advised quite well the dilution propotions for this gun.)
The downside is:
1. The manual sucks! Trial and error with lots of sheets of newspaper to practice on will help. Also, work on stuff that will not matter to acclimate your skill level. The manual is so bad that I learned to clean the gun the "old fashion way" i.e. common sense. I've been painting for 30+ years but finally took the plunge to a sprayer.
2. Did I say the manual sucks! Get a book from Taunton Press to really understand how to handle a sprayer.
I have finished natural wood projects by hand for 17+ years. Currently, I am finishing a maple mantel cap but will complete the project by hand until my confidence allows me to finish natural wood projects with this sprayer.
I was liberal with the five stars but still the manual sucks! Your results will be outstanding. It is a well-built, quality gun. Compressors are another story. I was running it on a pretty substantial 26 gallon compressor that ran the entire time I was spraying. My neighbors live close by, they didn't like me today. When I run nail guns on this compressor, it does not recycle nearly as bad.
If you are looking for a HVLP sprayer, this is it!
I returned the spray gun because of a defect. So, why the 5 stars? Well, I bought another one. I've read all the reviews here and learned a lot. The spray gun is of nice quality. The defect was that the trigger didn't press the air valve pin straight in. It gave the valve vertical motion, which made the valve hang up - giving it an erratic, jerky motion. Not only was it difficult to trigger, I assumed the valve would prematurely leak or fail.
So far, my only use has been to spray spar varnish on a exterior door. (horizontal, on sawhorses) . I had just read a book in which an expert stated that he had attempted to spray oil based varnish once, when he was young and stupid, and would never try it again. Being old and stupid, I used the 1.5 tip and thinned sparingly with a splash of thinner and a tablespoon or two of naphtha to a quart. I had to open the gun up fully - and it worked pretty well. Seeing the clear finish accumulate on the door was the problem: I'm using 66 year-old eyes here. I got a lot of pressure drop in 50' of air hose, and had to set my compressor regulator to deliver around 80 psi to the hose. I set the gun regulator to 35 or so. I was pleased with the results.
Other reviews have complained about the gun to air hose connection. Or, more specifically, the regulator to hose connection. It is 1/4 pipe thread - sort of. I got really lucky and noticed that a water supply hose worked perfectly as an extension hose. These may be referred to as compression fittings. The lucky part was noticing these at a Habitat for Humanity store for $1 each.
I used this gun with the 2.0 mm nozzle to spray acrlyic latex paint on a a cabinet I built. To get good results the gun should be held approx. 6 inches fron the surface and moved slowly and evenly. Also, latex paint should be thinned with 10% water. Water may raise the grain on wood so another round of sanding may be needed before the final coat. In addition, this spray gun uses a fair amount of compressed air. The owner's manual states that it requires 8.5 scfm @ 40 psi. My compressor is rated at 8.0 scfm @ 40 psi., so it runs constantly once I start spraying, just keeping up with the sprayer.
I purchased this spray gun and have used it several times. It has produced good results and I am completely happy with it. I did not have any problems (reported by others) with connecting the regulator and standard air hose fittings. I did use teflon tape on all threads.
Images ScreenShot
About Porter-Cable PSH1 Gravity Feed Spray Gun detail
Features
Related Product
Source From Best Price Porter Cable PSH1 Gravity Feed For Sale Best Buy Porter Cable PSH1 Gravity Feed Low Price Buy Cheap amp Review
Bye Bye
Cheers and Care
No response to “Porter-cable psh1 gravity feed spray gun”
Leave a reply